Home » Application » Fabrics & Textile » More FR Additive, Worse V-0: Stop Confusing Dripping with Drip-Ignition

More FR Additive, Worse V-0: Stop Confusing Dripping with Drip-Ignition

Views: 38     Author: Yinsu Flame Retardant     Publish Time: 2026-11-17      Origin: www.flameretardantys.com

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

More FR Additive, Worse V-0: Stop Confusing Dripping with Drip-Ignition

Eight bars at 1.6 mm, four of them set the cotton alight. Phosphorus already at 8%, LOI measured at 33. The lab concluded flame retardancy was done and V-0 was only a matter of time. Then a drip landed on the cotton and the cotton burned.


This is routine in Flame retardant PET. The usual response to failing at 8% is to add two more points, and the dripping gets worse. The direction was wrong from the start.


V-0 does not ban dripping

UL94's vertical burn page is unambiguous. Of the five criteria, exactly one concerns drips: the drip must not ignite the absorbent cotton below.

V-1 and V-2 carry identical time limits — 30 seconds per bar, 250 seconds total, 60 seconds of afterglow. The single line separating them is that criterion. V-2 permits a drip that ignites the cotton; V-1 does not.

A material that drips heavily but carries no flame downward can be V-0. A material that barely drips but sends one burning droplet into the cotton is V-2 at best.

1117-Yinsu flame retardant ZDP

Phosphorus extinguishes by dripping

This is the mechanism, not a defect. Phosphorus generates phosphoric and metaphosphoric acid, catalysing dehydration and charring, while accelerating polyester degradation so melt viscosity falls and the burning melt carries heat away. Remove the drip and you remove the cooling path.

A 2019 study in Synthetic Fiber Industry on a ZDP masterbatch makes the split visible: at 0.5% phosphorus the surface already formed a dense char with no dripping, and at 1.0% LOI reached 32.4% while UL94 stopped at V-1.

No dripping at 0.5%, still only V-1 at 1.0%. Anti-drip and afterflame suppression are separate thresholds, and the one that arrives first does not carry the other.

Three parameters decide whether the cotton ignites

1117-Yinsu Three parameters decide whether the cotton ignites

The first two are condensed-phase problems; the third is gas-phase. That is why adding phosphorus alone often fixes half the failure. Char forms, but the drip still carries flame, and the cotton burns anyway.


Why more makes it worse

Higher phosphorus means faster catalysed degradation, which means molecular weight collapses sooner in the burning zone. The char has not yet become continuous when the melt underneath thins out. At that point the char is not a barrier, it is debris. Large hot droplets fall, and the cotton ignites.

Going from 8% to 10% therefore buys a worse drip and a four-figure cost increase per tonne, with no rating change.


What ZDP actually delivers

Yinsu ZDP is zinc diethylphosphinate: white powder, ≥99% active content, melting near 200°C, decomposition above 320°C.

Its UL94 position can be stated plainly: V-0 from 1.6 mm to 3.2 mm, self-extinguishing on removal of the flame, with a small amount of dripping during burn that does not ignite the cotton.

"Some dripping" and "V-0" belong in the same sentence. One describes behaviour, the other describes a verdict. Keeping them separate in your datasheet is what prevents a customer from concluding, in his own lab, that the rating was invented.


Zinc oxide formed on heating is a Lewis acid. It catalyses dehydration and charring, bringing forward the moment the char becomes continuous, and it lifts melt viscosity so droplets are smaller and cooler. In the gas phase, PO· radicals interrupt the flame chain and hold t1 and t2 down.

Recommended loading is around 5%, reaching LOI above 30. Halogen-free, RoHS/REACH compliant, non-migrating, and the trace zinc improves antistatic behaviour in polyester. Packed 20 kg per bag.

1117-ZDP Zinc Diethyl Hypophosphite

Three detours and what they cost

Keep adding phosphorus: LOI climbs from 33 to 35, dripping worsens, the rating does not move, and cost arrives first.

Add PTFE: dripping drops sharply, but it is a fluoropolymer that some customer lists reject outright, and excess loading costs mechanical properties.

Switch to bromine: 8–12% reaches V-0 reliably, and one halogen restriction ends the export order.

All three search for something else to add, without asking which parameter of the drip actually failed.


Six questions

Q1: Does V-0 permit dripping?

Yes. The criterion is that drips must not ignite the cotton, not that drips are forbidden. Keep those two statements apart.


Q2: LOI is 33 and V-0 still fails — is the test wrong?

Unlikely. LOI measures the oxygen needed to sustain burning; V-0 measures afterflame, afterglow and drip behaviour once the flame is removed. The published 32.4% / V-1 case is exactly this gap.


Q3: Will a customer accept V-0 when he sees dripping?

The report decides, not the observation. If the cotton column reads "no", the rating is V-0. State "small amount of dripping, no ignition" up front rather than waiting to be asked.


Q4: Can a 1.6 mm report cover a 2.0 mm part?

Not by default. ZDP covers 1.6–3.2 mm, but the report must match the actual wall. The same formulation behaves differently at 1.6 and 3.2 mm because the thermal environment differs.


Q5: If 5% is not enough, can we jump to 8%?

Do not. Run 5, 6 and 7% at your own thickness, and watch afterflame and dripping separately. A three-point jump leaves you unable to tell dosage from dispersion.


Q6: Does red phosphorus also promote dripping?

Less than phosphate esters, since it chars in the condensed phase, but it carries colour and is limited to dark parts. Poor encapsulation or moisture control brings bloom.

Yinsu flame retardant is a factory, focuses on manufacturing non halogen, low smoke and non-toxic flame retardants for various of applications. 
We also supply tailor flame retardant solutions.
 
Office: No. 26, Kaitai Road, Huangpu District, Guangzhou City, Guangdong Province, China

Quick Links

Contact Us
Copyright 2022 Guangzhou Yinsu Flame Retardant New Material Co., Ltd. Technology by Leadong. Sitemap.