Home » Application » Engineering Plastics » Forty Degrees of Headroom: Measure PET Heat History in °C·min, Not in Setpoints

Forty Degrees of Headroom: Measure PET Heat History in °C·min, Not in Setpoints

Views: 39     Author: Yinsu flame retardant     Publish Time: 2026-11-21      Origin: www.flameretardantys.com

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Forty Degrees of Headroom: Measure PET Heat History in °C·min, Not in Setpoints


PET runs at 260–280°C. ZDP starts decomposing above 320°C.

Subtract the two and you have roughly 40°C. That is the entire margin you are giving the flame retardant. Nothing explodes at 300°C, but every extra minute at temperature spends part of the margin.

The formulation sheet does not show this. The same recipe runs clean at 265°C on line A; line B pushes to 285°C to fill a thin wall, and within two days the parts yellow, the smell appears and LOI drifts down. The instinct is to revise the formulation. The problem is heat history.

1121-Yinsu flame retardant ZDP ADP

Heat history is temperature multiplied by time

Most people watch the setpoint. 275°C looks safe because 45°C remains before 320°C.

Degradation is a function of time as well. At the same 275°C, a small fast-cycle part sits in the barrel for two or three minutes; a thick, long-cycle part sits for eight to ten. A threefold difference.

Combine both variables into one number:

°C·min = melt temperature × residence time

1121-Combine both variables into one number


The last two differ by under 4%. The last and the first differ by 2.8×.

This is an engineering approximation, not a kinetics model; Arrhenius owns that ground. It is good enough to compare two lines, two machines or two parts. In practice, treat 2,800 as the warning line — 280°C for ten minutes — and when you cross it, check colour, IV and smell.

Back pressure is missing from the formula and does real damage. High back pressure slows screw recovery, the melt is sheared repeatedly, and local temperature runs 10–15°C above the reading. The panel says 275; the melt may be at 290. The display shows barrel wall, not melt.


Station one: drying is chemistry, not heat history

PET is hygroscopic. Dry at 120°C for four hours to bring moisture below 0.04%.

Insufficient drying is not "a few bubbles". Water hydrolyses ester bonds in the melt, IV falls, chains break, parts embrittle and spinning breaks. You conclude the flame retardant made the material brittle. It was water.

Drying sits outside the 40°C window but amplifies what happens inside it. Material that has already lost IV degrades faster under high temperature and long residence. The combination is what people call "a bad batch".

Station two: ZDP melts at 200°C

ZDP melts near 200°C, sixty degrees below PET's melting range.

That gap has consequences. Entering the melting zone, ZDP is already liquid while the chip is still softening. It does not need screw shear to break up solid agglomerates; dispersion happens in the phase change.

The cost is real: a low-viscosity liquid plasticises the PET melt and viscosity drops a notch. Good for dispersion, bad for dripping. The zinc charring action is the necessary compensation, not an optional extra — a continuous char layer means the lost viscosity does not turn into large droplets.

1118-ZDP Zinc Diethyl Hypophosphite

ADP powder takes the other route: high melting point, solid particles throughout, dispersion entirely by screw. Same screw and same residence, and a coarse or agglomerated batch leaves a problem in front of the spinneret.

Station three: tens of microns decide everything

Spinneret capillaries are tens of microns across. Any particle larger than the capillary plugs it.

One plugged hole unbalances the bundle: first fly, then breaks. Enough breaks and the pack comes off, two hours minimum.

The number to watch here is not temperature but the rate of rise of filter pressure value. A steep curve means particulate in the melt, either poor dispersion or a coarse grade. A flat curve means process and material match.

Injection moulding swaps this for mould deposit. Light deposit dulls gloss; heavy deposit blocks vents and brings burns and short shots. Half the diagnosis is colour: white deposit is usually additive bloom, black is scorched material from poor venting.

Station four: storage and regrind

20 kg paper-plastic bags. A damp warehouse and high stacking give caked material at the bottom of the pallet, which blocks the hopper. Breaking the cake by hand leaves the batch uneven.

Regrind deserves its own line. Recycled PET already carries lower IV; adding flame retardant drops it further. Above 30% regrind, re-validate both rating and mechanicals. Do not reuse the virgin report.

Control point

1121-Five production stages, five control points

Five questions

Q1: Decomposition at 320°C — can we run at 300°C?

No. 320°C is the onset threshold, not a working temperature. At 300°C you hold 20°C of margin, and any local hot spot crosses it. Margin means staying away from it.

Q2: How do you measure residence time?

Crude but effective: drop a handful of colour masterbatch in before stopping feed and time it from hopper to nozzle. Or divide barrel volume by shot size. The error is large, but it answers the only question that matters — is this line at three minutes or eight?

Q3: Does ZDP need side feeding?

No. It melts at 200°C, feeds from the main throat and disperses in the melting zone. Side feeding works but does not justify modifying the machine.

Q4: Is a fast-rising filter pressure always the flame retardant?

No. Rule out three things first: particle size and dispersion, screen mesh, regrind ratio.

Q5: Can drying time be shortened?

Not by cutting time. Use a desiccant dryer and lower the dew point. Hot-air drying struggles in humid seasons, and with a thick bed the surface dries while the core does not.

Yinsu flame retardant is a factory, focuses on manufacturing non halogen, low smoke and non-toxic flame retardants for various of applications. 
We also supply tailor flame retardant solutions.
 
Office: No. 26, Kaitai Road, Huangpu District, Guangzhou City, Guangdong Province, China

Quick Links

Contact Us
Copyright 2022 Guangzhou Yinsu Flame Retardant New Material Co., Ltd. Technology by Leadong. Sitemap.